1150kW光伏+300kW储能+250kW PCS光储充一体化直流构网系统 | 750V直流母线·23路光伏接入·构网型·98%高效 | 1150kW PV + 300kW Storage + 250kW PCS Integrated PV-Storage-Charging DC Grid-Forming System | 750V DC Bus · 23 PV Channels · Grid-Forming · 98% Efficiency
|
出品方:稳利达电力电子 | Wenlida Power Electronics |
项目简介 | Project Introduction
本项目为光储充一体化直流构网系统,由稳利达电力电子提供整套光伏接入、储能充放电、并网变流与直流母线构网解决方案。系统由23台50kW光伏DCDC(合计1150kW)、3台100kW储能DCDC(合计300kW)与2台125kW PCS(合计250kW)构成,公共直流母线额定750Vdc,并配置600kW直流750V接口与10kW直流750V接口。设备将200-700Vdc光伏直流升压汇集至750V母线,储能侧300-700Vdc经3路100kW双向DCDC实现充放电,经PCS逆变为AC400V三相输出(配隔离变压器),直流母线同时直供直流充电桩与直流负载,形成"直流构网、多能互补"的源网荷储架构。各模块转换效率98%,电压/电流稳定度静态±1%、动态±3%,支持MPPT与恒压自动切换、恒压恒流充放电;整机配置触摸屏与RS485(Modbus RTU)/以太网(Modbus TCP)通讯,具备母线绝缘监测、直流回路过流与漏电流检测、分励脱扣与故障支路快速切除能力。适用于园区光储充一体站、直流微电网、构网型直流配电与新能源就地消纳场景。
This project is an integrated PV-storage-charging DC grid-forming system, delivered by Wenlida Power Electronics as a complete solution for PV access, battery charge/discharge, grid-tied conversion and DC bus grid forming. It comprises twenty-three 50kW PV DC-DC converters (1150kW total), three 100kW storage DC-DC converters (300kW total) and two 125kW PCS units (250kW total), with a 750Vdc rated common DC bus plus a 600kW and a 10kW 750Vdc interface. PV arrays at 200-700Vdc are stepped up and collected onto the 750V bus; the storage side at 300-700Vdc charges and discharges through three 100kW bidirectional channels; PCS units invert to AC400V three-phase (with isolation transformer), while the DC bus directly feeds DC chargers and DC loads — a source-grid-load-storage architecture of "DC grid forming and multi-energy complementarity." Module efficiency is 98%, voltage/current stability ±1% static and ±3% dynamic, with MPPT-to-CV automatic switching and CV/CC charge-discharge; the system provides a touch screen with RS485 (Modbus RTU) / Ethernet (Modbus TCP) communication, bus insulation monitoring, DC over-current and leakage-current detection, shunt-trip breakers and fast faulty-branch disconnection. It suits park-level PV-storage-charging stations, DC micro-grids, grid-forming DC distribution and on-site renewable consumption.
系统拓扑说明 | System Topology Description

|
图1:系统拓扑图 | Figure 1: System Topology Diagram |
|
图2:光储充一体化直流构网系统应用场景(见下方配图)| Figure 2: Integrated PV-storage-charging DC grid-forming system application scenario (see image below) |
图2:光储充一体化直流构网系统应用场景 | Figure 2: Integrated PV-storage-charging DC grid-forming system application scenario
整套系统采用750Vdc公共直流母线架构。光伏侧分23路接入(每路50kW,200-700Vdc),经光伏DCDC升压汇集至750V母线;储能侧分3路接入(每路100kW,300-700Vdc),经双向DCDC实现充电与放电;并网侧由2台125kW PCS并联输出AC400V三相(配隔离变压器);直流侧另设600kW与10kW两路750V接口,直供直流充电桩与直流负载。系统提供一只10寸触摸屏供客户监控数据与触摸操作,并提供一路RS485接口实现遥控、遥测、遥调功能。整机由PCS柜(1200×1000×2260mm,2台)、光伏柜(800×800×2260mm,6台)、储能柜(800×800×2260mm,1台)与负载柜(800×800×2260mm,1台)组成,功率模块与机柜为模块化组合,便于扩容与维护。
The system adopts a 750Vdc common DC bus architecture. PV is connected through twenty-three channels (50kW each, 200-700Vdc) and stepped up onto the 750V bus; storage is connected through three channels (100kW each, 300-700Vdc) with bidirectional DC-DC; the grid side uses two paralleled 125kW PCS units outputting AC400V three-phase (with isolation transformer); two additional DC interfaces of 600kW and 10kW at 750V directly feed DC chargers and DC loads. A 10-inch touch screen provides local monitoring and touch operation, and one RS485 port supports remote telecontrol, telemetry and tele-adjustment. The system is built from two PCS cabinets (1200×1000×2260mm), six PV cabinets (800×800×2260mm), one storage cabinet (800×800×2260mm) and one load cabinet (800×800×2260mm); modules and cabinets are modular for easy expansion and maintenance.
完整全套参数表 | Complete Parameter Tables
表1 50kW光伏DCDC(1-23)电气参数 | Table 1 Electrical Parameters of 50kW PV DC-DC (Channels 1-23)
|
序号 No. |
电气类目 Category |
详细类目 Item |
规格 Specification |
|
1 |
直流电压 DC Voltage |
光伏侧 PV Side |
200-700Vdc |
|
|
|
母线侧 Bus Side |
额定 750Vdc |
|
2 |
直流电流 DC Current |
光伏侧 PV Side |
不大于 120A |
|
|
|
母线侧 Bus Side |
不大于 67A |
|
3 |
转换效率 Efficiency |
高压750V,低压600V |
98%(实验条件下取得) |
|
4 |
额定功率 Rated Power |
|
50kW |
|
5 |
工作模式 Mode |
MPPT |
可设置,MPPT、恒压自动切换 |
|
6 |
电压稳定度 Voltage Stability |
静态 / 动态 Static / Dynamic |
±1% / ±3% |
|
7 |
电流稳定度 Current Stability |
静态 / 动态 Static / Dynamic |
±1% / ±3% |
|
8 |
通信接口 Communication |
RS485 / CAN |
全隔离,Modbus RTU / CAN2.0A/B **1M/S |
|
9 |
供电方式 Power Supply |
|
220Vac |
|
10 |
设置方式 Configuration |
|
通信方式通过 PC 或上位机设置 |
|
11 |
保护 Protection |
|
高压侧过压/欠压、低压侧过压/欠压、过流、过温、通讯保护,解除后自动恢复 |
|
12 |
尺寸 Dimension |
长×宽×高 L×W×H |
500×250×154mm(不含接线端子) |
|
13 |
重量 Weight |
|
21kg |
|
14 |
操作方式 Operation |
|
可自动或通信控制 |
|
15 |
散热方式 Cooling |
|
风冷 |
表2 100kW储能DCDC(31-33)电气参数 | Table 2 Electrical Parameters of 100kW Storage DC-DC (Channels 31-33)
|
序号 No. |
电气类目 Category |
详细类目 Item |
规格 Specification |
|
1 |
直流电压 DC Voltage |
储能侧 Storage Side |
300-700Vdc |
|
|
|
母线侧 Bus Side |
额定 750Vdc |
|
2 |
直流电流 DC Current |
储能侧 Storage Side |
不大于 200A |
|
|
|
母线侧 Bus Side |
不大于 134A |
|
3 |
转换效率 Efficiency |
高压750V,低压600V |
98%(实验条件下取得) |
|
4 |
额定功率 Rated Power |
|
100kW |
|
5 |
工作模式 Mode |
|
恒压、恒流 |
|
6 |
电压稳定度 Voltage Stability |
静态 / 动态 Static / Dynamic |
±1% / ±3% |
|
7 |
电流稳定度 Current Stability |
静态 / 动态 Static / Dynamic |
±1% / ±3% |
|
8 |
通信接口 Communication |
RS485 / CAN |
全隔离,Modbus RTU / CAN2.0A/B **1M/S |
|
9 |
供电方式 Power Supply |
|
220Vac |
|
10 |
设置方式 Configuration |
|
通信方式通过 PC 或上位机设置 |
|
11 |
保护 Protection |
|
高压侧过压/欠压、低压侧过压/欠压、过流、过温、通讯保护,解除后自动恢复 |
|
12 |
尺寸 Dimension |
长×宽×高 L×W×H |
600×363×154mm(不含接线端子) |
|
13 |
重量 Weight |
|
37kg |
|
14 |
操作方式 Operation |
|
可自动或通信控制 |
|
15 |
散热方式 Cooling |
|
风冷 |
表3 125kW PCS(2台)电气参数 | Table 3 Electrical Parameters of 125kW PCS (2 units)
|
类别 Category |
项目 Item |
规格 Specification |
|
直流侧 |
电压范围 Voltage Range |
650-850Vdc |
|
**大输出功率 Max. Output Power |
125kW |
|
|
**大输出电流 Max. Output Current |
203A |
|
|
交流并网 |
输出线制 Wiring |
3W+N+PE / 3W+PE |
|
额定功率 Rated Power |
125kW |
|
|
额定电压 Rated Voltage |
AC400V |
|
|
额定电流 Rated Current |
200A |
|
|
电压范围 Voltage Range |
-15% ~ +15% |
|
|
额定频率 Rated Frequency |
50Hz |
|
|
功率因数 PF |
-0.9 ~ 0.9 |
|
|
输出谐波 THD |
≤3%(额定功率) |
|
|
环境 |
工作温度 Operating Temp. |
-20 ~ +50℃(45℃以上降额) |
|
相对湿度 Humidity |
0 ~ 95%RH,无冷凝 |
|
|
工作海拔 Altitude |
2000m(2000~4000m降额使用) |
|
|
其他 |
通信接口 Communication |
RS485 |
|
防护等级 Protection Class |
IP20(强制通风) |
|
|
尺寸 Dimension (W×D×H) |
440×255×620mm(不含把手与接线端子) |
|
|
重量 Weight |
70kg |
表4 整机规格参数 | Table 4 Complete System Specifications
|
端口 Port |
项目 Item |
参数 Parameter |
|
光伏接口 1-23 |
**大输入功率 Max Input Power |
50kW(每路 per channel,合计 1150kW) |
|
**大输入电压 Max Input Voltage |
700V |
|
|
MPPT电压范围 MPPT Range |
200-700V |
|
|
**大输入电流 Max Input Current |
120A(每路 per channel) |
|
|
MPPT数量 MPPT Count |
1(每路 per channel) |
|
|
储能接口 1-3 |
电池电压范围 Battery Voltage |
300-700V |
|
**大电流 Max Current |
200A(每路 per channel) |
|
|
额定功率 Rated Power |
100kW(每路 per channel,合计 300kW) |
|
|
电网接口 1-2 |
输出线制 Wiring |
3W+PE |
|
额定功率 Rated Power |
500kW |
|
|
额定电压 Rated Voltage |
AC400V(范围 320-460Vac) |
|
|
**大电流 Max Current |
800A |
|
|
额定频率 Rated Frequency |
50Hz |
|
|
功率因数 PF |
-0.9 ~ 0.9 |
|
|
隔离 Isolation |
隔离变压器 |
|
|
直流750V接口1 |
额定功率 Rated Power |
600kW |
|
额定电压 Rated Voltage |
750V |
|
|
额定电流 Rated Current |
800A |
|
|
直流750V接口2 |
额定功率 Rated Power |
10kW |
|
额定电压 Rated Voltage |
750V |
|
|
额定电流 Rated Current |
13.3A |
|
|
基本参数 |
工作温度范围 Operating Temp. |
-10 ~ +55℃(大于45℃降额使用) |
|
相对湿度 Humidity |
0 ~ 90%,无冷凝 |
|
|
**工作海拔 Max Altitude |
2000m(大于2000m降额使用) |
|
|
冷却方式 Cooling |
风冷 |
|
|
显示 Display |
10寸触摸屏 |
|
|
系统供电 Power Supply |
AC220V(由用户提供) |
|
|
通讯方式 Communication |
RS485(Modbus RTU) / 以太网(Modbus TCP) |
|
|
防护等级 Protection Class |
IP20 |
|
|
整机尺寸 System Dimension |
PCS柜 1200×1000×2260mm(2台);光伏柜 800×800×2260mm(6台);储能柜 800×800×2260mm(1台);负载柜 800×800×2260mm(1台)(暂定) |
系统保护 | System Protection
? 所有断路器均带分励脱扣功能及反馈触点;
? DC750V母线配备母线绝缘监测功能;
? 直流回路均配置电流检测,检测到过流时切除故障支路断路器,避免影响整个系统;
? 直流回路均配置漏电流检测,检测到漏电流时切除故障支路断路器,避免影响整个系统。
? All circuit breakers are equipped with shunt-trip function and feedback contacts;
? The DC750V bus is provided with bus insulation monitoring;
? Every DC circuit has current detection; on over-current the faulty branch breaker is tripped to protect the whole system;
? Every DC circuit has leakage-current detection; on leakage the faulty branch breaker is tripped to protect the whole system.
搬运说明 | Handling Instructions
|
图3:搬运示意图 | Figure 3: Handling Diagram |
机柜底座开有两个方形孔,搬运时叉车两根货叉通过方形孔叉入机柜底部;移动过程中须保证缓慢、平稳,避免倾斜与冲击。
Two square openings are provided in the cabinet base. During handling, the two forks of the forklift are inserted through these openings into the bottom of the cabinet. Movement must be slow and steady to avoid tilting and impact.
应用场景 | Application Scenarios
典型应用 | Typical Applications
? 园区光储充一体化充电站、直流快充
? 构网型直流配电与直流建筑
? 工商业光伏就地消纳与峰谷套利
? 直流微电网、离网/并网混合供电
? 新能源配储与直流母线多端口能量管理
? Park-level integrated PV-storage-charging stations and DC fast charging
? Grid-forming DC distribution and DC buildings
? On-site PV consumption and peak-valley arbitrage for C&I users
? DC micro-grids and off-grid/grid-tied hybrid supply
? Renewable-plus-storage and multi-port DC bus energy management
|
定制说明:稳利达电力电子本系列产品支持定制开发,可根据光伏路数、储能容量、直流母线电压、PCS功率与通讯协议灵活配置,适配不同光储充一体与直流构网应用需求。 Customization Note: Customization available by Wenlida Power Electronics. Number of PV channels, storage capacity, DC bus voltage, PCS power and communication protocol can be flexibly configured according to site conditions to meet various integrated PV-storage-charging and DC grid-forming application requirements. |