600kW光伏+360kW储能+400kW PCS光储一体系统 | 920V直流母线·10寸触摸屏·三柜一体化·98%高效 | 600kW PV + 360kW Storage + 400kW PCS Integrated PV-Storage System | 920V DC Bus · 10-inch Touch Screen · Three-Cabinet Integration · 98% Efficiency
|
出品方:稳利达电力电子 | Wenlida Power Electronics |
项目简介 | Project Introduction
本项目为光储一体系统,由稳利达电力电子提供整套光伏接入、储能充放电与并网变流一体化解决方案。系统由3台200kW光伏DCDC、6台60kW储能DCDC与4台100kW PCS(合计400kW)构成,光伏总容量600kW、储能总容量360kW、并网容量400kW,公共直流母线额定920Vdc。设备将200-892Vdc光伏直流升压汇集至920V母线,储能侧520-897Vdc经6路60kW双向DCDC实现充放电,再由4台PCS逆变为AC400V三相并入电网(带隔离变压器)。各模块转换效率98%,电压/电流稳定度静态±1%、动态±3%,支持MPPT与恒压自动切换、恒压恒流充放电,配置10寸本地触摸屏与RS485/CAN全隔离通讯,保护完备,故障解除后自动恢复运行。适用于园区光储充、工商业峰谷套利、微电网与分布式光储一体化场景。
This project is an integrated PV-storage system, delivered by Wenlida Power Electronics as a complete solution for PV access, battery charge/discharge and grid-tied conversion. It comprises three 200kW PV DC-DC converters, six 60kW storage DC-DC converters and four 100kW PCS units (400kW total), with 600kW PV capacity, 360kW storage capacity, 400kW grid-tied capacity and a common 920Vdc DC bus. PV arrays at 200-892Vdc are stepped up and collected onto the 920V bus; the storage side at 520-897Vdc charges and discharges through six 60kW bidirectional DC-DC channels; four PCS units then invert to AC400V three-phase and feed the grid (with isolation transformer). Module efficiency is 98%, voltage/current stability ±1% static and ±3% dynamic, MPPT-to-CV automatic switching and CV/CC charge-discharge are supported, with a 10-inch local touch screen and fully isolated RS485/CAN communication, comprehensive protections and auto-recovery after fault clearance. It suits park-level PV-storage-charging, commercial peak-valley arbitrage, micro-grids and distributed integrated PV-storage.
系统拓扑说明 | System Topology Description

|
图1:系统拓扑图 | Figure 1: System Topology Diagram |
|
图2:光储一体系统应用场景(见下方配图)| Figure 2: Integrated PV-storage system application scenario (see image below) |
图2:光储一体系统应用场景 | Figure 2: Integrated PV-storage system application scenario
整套系统采用公共直流母线架构,母线额定920Vdc。光伏侧分3路接入(每路200kW,200-892Vdc),经光伏DCDC升压后汇集至920V母线;储能侧分6路接入(每路60kW,520-897Vdc),经双向DCDC实现充电与放电;并网侧由4台100kW PCS并联构成400kW,逆变为AC400V三相输出,配置隔离变压器。系统提供一只10寸触摸屏供客户监控数据与触摸操作,并提供一路RS485接口实现遥控、遥测、遥调功能。整机由光伏DC柜(800×1000×2100mm)、储能DC柜(1000×1000×2100mm)与PCS柜(1200×1000×2300mm)组成。
The system adopts a common DC bus architecture with a 920Vdc rated bus. PV is connected through three channels (200kW each, 200-892Vdc) and stepped up onto the 920V bus; storage is connected through six channels (60kW each, 520-897Vdc) with bidirectional DC-DC for charging and discharging; the grid side uses four paralleled 100kW PCS units for 400kW total, inverting to AC400V three-phase output with an isolation transformer. A 10-inch touch screen provides local data monitoring and touch operation, and one RS485 port supports remote telecontrol, telemetry and tele-adjustment. The system consists of a PV DC cabinet (800×1000×2100mm), a storage DC cabinet (1000×1000×2100mm) and a PCS cabinet (1200×1000×2300mm).
完整全套参数表 | Complete Parameter Tables
表1 200kW光伏DCDC(1-3)电气参数 | Table 1 Electrical Parameters of 200kW PV DC-DC (Channels 1-3)
|
序号 No. |
电气类目 Category |
详细类目 Item |
规格 Specification |
|
1 |
直流电压 DC Voltage |
光伏侧 PV Side |
200-892Vdc |
|
|
|
母线侧 Bus Side |
额定 920Vdc |
|
2 |
直流电流 DC Current |
光伏侧 PV Side |
不大于 350A |
|
|
|
母线侧 Bus Side |
不大于 218A |
|
3 |
转换效率 Efficiency |
高压750V,低压600V |
98%(实验条件下取得) |
|
4 |
额定功率 Rated Power |
|
200kW |
|
5 |
工作模式 Mode |
MPPT |
可设置,MPPT、恒压自动切换 |
|
6 |
电压稳定度 Voltage Stability |
静态 / 动态 Static / Dynamic |
±1% / ±3% |
|
7 |
电流稳定度 Current Stability |
静态 / 动态 Static / Dynamic |
±1% / ±3% |
|
8 |
通信接口 Communication |
RS485 / CAN |
全隔离,Modbus RTU / CAN2.0A/B **1M/S |
|
9 |
供电方式 Power Supply |
|
220Vac |
|
10 |
设置方式 Configuration |
|
通信方式通过 PC 或上位机设置 |
|
11 |
保护 Protection |
|
高压侧过压/欠压、低压侧过压/欠压、过流、过温、通讯保护,解除后自动恢复 |
|
12 |
尺寸 Dimension |
长×宽×高 L×W×H |
600×543×154mm(不含接线端子) |
|
13 |
重量 Weight |
|
55kg |
|
14 |
操作方式 Operation |
|
可自动或通信控制 |
|
15 |
散热方式 Cooling |
|
风冷 |
表2 60kW储能DCDC(4-9)电气参数 | Table 2 Electrical Parameters of 60kW Storage DC-DC (Channels 4-9)
|
序号 No. |
电气类目 Category |
详细类目 Item |
规格 Specification |
|
1 |
直流电压 DC Voltage |
储能侧 Storage Side |
520-897Vdc |
|
|
|
母线侧 Bus Side |
额定 920Vdc |
|
2 |
直流电流 DC Current |
储能侧 Storage Side |
不大于 85A |
|
|
|
母线侧 Bus Side |
不大于 66A |
|
3 |
转换效率 Efficiency |
高压750V,低压600V |
98%(实验条件下取得) |
|
4 |
额定功率 Rated Power |
|
60kW |
|
5 |
工作模式 Mode |
|
恒压、恒流 |
|
6 |
电压稳定度 Voltage Stability |
静态 / 动态 Static / Dynamic |
±1% / ±3% |
|
7 |
电流稳定度 Current Stability |
静态 / 动态 Static / Dynamic |
±1% / ±3% |
|
8 |
通信接口 Communication |
RS485 / CAN |
全隔离,Modbus RTU / CAN2.0A/B **1M/S |
|
9 |
供电方式 Power Supply |
|
220Vac |
|
10 |
设置方式 Configuration |
|
通信方式通过 PC 或上位机设置 |
|
11 |
保护 Protection |
|
高压侧过压/欠压、低压侧过压/欠压、过流、过温、通讯保护,解除后自动恢复 |
|
12 |
尺寸 Dimension |
长×宽×高 L×W×H |
600×363×154mm(不含接线端子) |
|
13 |
重量 Weight |
|
21kg |
|
14 |
操作方式 Operation |
|
可自动或通信控制 |
|
15 |
散热方式 Cooling |
|
风冷 |
表3 100kW PCS电气参数(4台并联400kW)| Table 3 Electrical Parameters of 100kW PCS (4 units, 400kW)
|
类别 Category |
项目 Item |
规格 Specification |
|
直流侧 |
电压范围 Voltage Range |
615-950V(3W+PE)/ 650-950V(3W+N+PE) |
|
**大输出功率 Max. Output Power |
105kW |
|
|
**大输出电流 Max. Output Current |
170A |
|
|
交流并网 |
输出线制 Wiring |
三相三线(3W+PE)/ 三相四线(3W+N+PE) |
|
额定功率 Rated Power |
100kW |
|
|
额定电压 Rated Voltage |
AC400V |
|
|
额定电流 Rated Current |
167A |
|
|
电压范围 Voltage Range |
-15% ~ +15% |
|
|
额定频率 Rated Frequency |
50Hz |
|
|
功率因数 PF / THDi |
1超前~1滞后(可设置)/ THDi ≤3%(额定功率) |
|
|
环境 |
工作温度 Operating Temp. |
-20 ~ +50℃(45℃以上降额) |
|
相对湿度 Humidity |
0 ~ 95%RH,无冷凝 |
|
|
工作海拔 Altitude |
4000m(2000~4000m降额使用) |
|
|
其他 |
通信接口 Communication |
RS485、CAN |
|
防护等级 Protection Class |
IP20(智能强制风冷) |
|
|
尺寸 Dimension (W×D×H) |
500×670×255mm |
|
|
重量 Weight |
50kg |
表4 整机规格参数 | Table 4 Complete System Specifications
|
端口 Port |
项目 Item |
参数 Parameter |
|
光伏接口 1-3 |
**大输入功率 Max Input Power |
200kW(每路 per channel) |
|
**大输入电压 Max Input Voltage |
892V |
|
|
MPPT电压范围 MPPT Range |
200-892V |
|
|
**大输入电流 Max Input Current |
350A |
|
|
MPPT数量 MPPT Count |
1(每路 per channel) |
|
|
储能接口 1-6 |
电池电压范围 Battery Voltage |
520-897V |
|
**大电流 Max Current |
85A(每路 per channel) |
|
|
额定功率 Rated Power |
60kW(每路 per channel) |
|
|
电网接口 |
输出线制 Wiring |
3W+N+PE / 3W+PE |
|
额定功率 Rated Power |
400kW |
|
|
额定电压 Rated Voltage |
AC400V(范围 320-460Vac) |
|
|
额定电流 Rated Current |
668A |
|
|
额定频率 Rated Frequency |
50Hz |
|
|
功率因数 PF |
1超前~1滞后(可设置) |
|
|
隔离 Isolation |
带隔离变压器 |
|
|
基本参数 |
工作温度范围 Operating Temp. |
-10 ~ +45℃ |
|
相对湿度 Humidity |
0 ~ 90%,无冷凝 |
|
|
**工作海拔 Max Altitude |
2000m |
|
|
冷却方式 Cooling |
风冷 |
|
|
显示 Display |
10寸触摸屏 |
|
|
系统供电 Power Supply |
AC220V(由用户提供) |
|
|
通讯方式 Communication |
RS485(Modbus RTU) / 以太网(Modbus TCP) |
|
|
防护等级 Protection Class |
IP54 |
|
|
整机尺寸 System Dimension |
光伏DC柜 800×1000×2100mm;储能DC柜 1000×1000×2100mm;PCS柜 1200×1000×2300mm(暂定) |
搬运说明 | Handling Instructions
机柜底座开有两个方形孔,搬运时叉车两根货叉通过方形孔叉入机柜底部;移动过程中须保证缓慢、平稳,避免倾斜与冲击。
Two square openings are provided in the cabinet base. During handling, the two forks of the forklift are inserted through these openings into the bottom of the cabinet. Movement must be slow and steady to avoid tilting and impact.
应用场景 | Application Scenarios
典型应用 | Typical Applications
? 园区光储充一体化、光伏就地消纳
? 工商业峰谷套利与需量管理
? 分布式光储系统、直流微电网
? 储能电站直流侧变换与并网
? 新能源配储、离网/微网供电
? Park-level PV-storage-charging and on-site PV consumption
? Commercial and industrial peak-valley arbitrage and demand management
? Distributed PV-storage systems and DC micro-grids
? DC-side conversion and grid connection for storage plants
? Renewable-plus-storage and off-grid/micro-grid supply
|
定制说明:稳利达电力电子本系列产品支持定制开发,可根据光伏容量、储能容量、并网电压等级与通讯协议灵活配置,适配不同光储一体与直流微网应用需求。 Customization Note: Customization available by Wenlida Power Electronics. PV capacity, storage capacity, grid-tied voltage class and communication protocol can be flexibly configured according to site conditions to meet various integrated PV-storage and DC micro-grid application requirements. |